A Simple Guide For Painting Walls, Windows, And Doors The Right Way

Can anyone paint a room? Yes, anyone is capable of painting a room, and it can look very appealing. But, another question comes in, how good will it look? Will it be satisfying? The answer to these issues will automatically be no because they can paint but they can’t reach a professional goal.

guide for painting walls, windows, and doors

  1. Sand the wall, trim, and door.

Before starting to sand, you can first clean it. Cleaning can be done using soap solution and a piece of rag to remove any dust and grease on the walls that may alter the final appearance. Wait until it dries up. Now that they are clean, you can start by sanding wood works first. Do this using a 120-grit sandpaper. Fill nail holes with a filler, wait until they dry and sand again.

On edges and corners, you can use a sanding sponge, enabling you to reach all surface as it can merge into any shape. After sanding, do not forget to dust the surfaces again using a dry rag.

  1. Apply the prime.

First, tape the regions you may not want the paint to get on them. The ends of the sticker should extend up to where the trim meets the wall and protect areas of the trim where paint should not reach. Now you can apply your prime. Note that bare walls need an oil-based primer. Wood surfaces also need priming so that other coats can adhere well. You can now leave the primer for at least 12 hours to dry. Sand using 220-grit sandpaper gently and dust again.

  1. Check grooves.

If they are cracks or holes in the wall, you can get rid of them using a filling compound. Wait for the mixture to dry well. Then sand that area and prime it.

  1. Fill the joints.

It is necessary to fill the spaces found between wood works and the wall using a caulk gun. Just put enough caulk on the joints. Too much caulk wills results to bumps between the wall and wood works.

You can first start by painting the ceiling. Sink a two-inch brush into the paint ensuring only a third of the brush bristles coated with paint. Run the brush along the ends of the roof. Continue applying the paint straight until you finish all sides. Clean the paint that landed on the wrong spot. After cleaning, you can now paint your ceiling entirely using a roller that has a log handle. Dip the roller into the paint. Roll it to ensure that you equally cover the roller with paint. Roll the paint onto the ceiling starting from a corner. Without removing the roller, fill all patches. Continue adding paint to the roller until the whole ceiling is painted.

Painting wood works also follow a simple procedure. Apply the first coat on the wood works and wait until it dries up. Sand it using a 220-grit sandpaper and dust. Paint the final layer. Windows and doors cannot be painted using the same procedures and try as much as possible to prevent paint from reaching the glass.

The last step is painting the walls. When the wood works are completely dry, you can tape their edges to protect them from wall paint. Also using a two-inch brush, apply paint to the door and window trim, ceiling and edges of wood works. Using an extended roller paint the wall top to the bottom. Make sure to cover all empty patches. Continue adding paint to the roller until the entire wall is painted.

Remember to remove protecting tapes when the paint is still wet, thus helps to avoid removing patches of paints when it dries.

Read More

Blunders to Avoid When Painting Kitchen Cabinets

Painted cabinets are the new swag and as such, happens to rule as updating of the kitchen with a few additional color coats is an idea people love. No second thoughts happen to cross people’s mind as about this particular perception, but little do they comprehend the pitfalls associated with it. Some most common blunders to avoid in this particular undertaking include:

  1. Blunders to Avoid When Painting Kitchen CabinetsHaving unrealistic expectations.

The lovely nature of the cabinets is a good result, but the smooth nature they portray is not going to be obvious especially if the cabinets happen to have an open grain.  The paint will not cover the grooves on the cabinets and hence the rough aspect of the cabinets. Another thing is that stains on the cabinet surfaces become more evident and visible in after the new paint coat dries. Putty is the right material to fill the grains, and this can be a very long and labor-intensive process.

  1. Allocating insufficient time.

It is a common belief that the application of a new coat of paint is an activity done over the weekend and completed successfully. Well, this a misplaced opinion as the whole business can take at least four days and stretch to even a week of the event as the prep time for the job also plays a significant role in the whole paint application job.

  1. Non-removal of the drawers and doors off.

A very crucial step in the cabinet printing job. Remove all the hardware such as the hinges and knobs. Pull out the drawers then take off the doors. Mistakes begin to happen the moment people tend to associate painting everything on the cabinet with time saving. However, it is not an ideal idea as the cabinet hardware is likely to wear very soon and start chipping.

  1. Non-identification of where the hardware, drawers and doors go.

After removing the hardware bits, it is evident that you need to glue back the parts to the original positions. Non-identification and marking of where each primary tool was to go may be disastrous in case one forgets. A tape with number label can help solve the problem.

  1. Skipping of sanding.

No matter the condition of the cabinet surfaces, sanding is still an essential process in the cabinet repainting idea, because it helps in the creation of surfaces to which paint can easily stick. A middle-spectrum sandpaper is the best option for this kind of sanding.

  1. Dust filled surface before painting.

Dust on the cabinet surface creates an impression of one who has painted over sand and this lead to a rough finish. The correction of such an error involves sanding down all over again and then repainting. For you to avoid such, it is necessary to vacuum any dirt and debris before engaging in the actual painting process.

  1. Non-priming.

It is easy to overlook and skip this particular step, but the consequences are not very pleasant as it leads to almost immediate bleeding of the paint from knots in the wood. The immediate result is a fantastic kitchen, but it does not last long. When using a primer, the stain blocking primer is the best option as blotches are not likely to occur in the curing process of the paint.

  1. Choosing the wrong color

It is hard to point out that particular colors are right for the kitchen. Getting it right the first time for the cabinet though is crucial because the color choice is not appealing as originally thought. Testing the color type on paper and hanging it strategically in the kitchen location to see whether it matches is a good idea before actually considering the color.

  1. Cheap paint.

A good paint guarantees a smoother finish. Moreover, going for the best paint can be cost effective especially in the part that involves hiring a professional to do the job. It is easier to do the job alone instead of hiring one.

Brush marks at the end of the task should not be a headache as the spray gun, or a smoothing roller can quickly help solve that particular one.

Read More

Decorative Painting 101 – Gradient Effect 

Are you for the notion of having different results after painting a wall? Try adding depth and texture by fading your paint colors smoothly onto each other. A technique that provides a gradient effect to your surface. Try imagining a wall that is smooth in gradient with colors from light yellow at the top of the wall, and dark orange towards the floor.

Decorative Painting 101 – Gradient EffectIn addition to getting a fading down look, light reflected off this particular wall turns out to be unique. Equally, you can decide to fade as many as six to seven shades of the same color just to have fun.

Before you begin splashing the wall with your paint, perform numerous tests on a piece of plywood. It will not only provide you with an idea of which colors you would like to utilize but also let gives you some time to practice on perfecting the gradient fading process.

  1. Tools and Materials

For instance, you need some materials beforehand for a three-color fade including; paint brushes, painter’s tape, a sea sponge, plastic tarp, paint pan, water, spray bottles and finally the three shades of color you want to use.

  1. Step by step guide

First, you need to cover the floor by laying down a canvas tarp or plastic. For you to be sure that the tape does not stick on your feet as you walk around, fasten it to the baseboards using painter’s tape by placing the tape in areas where the baseboard joins with the wall.

As you work with the tape, cover every other area that you would not wish to spray paint by sticking them with paint. These are areas like electrical outlets and windows.

With that done, you are set to use a clean paint roller. For the paint that you intend to apply at the center of your gradient, pour it into your paint pan. Use a paint roller to stain the two-thirds at the center of the surface with the medium-tone. You have to move fast, to limit the coat from drying before you continue to apply the remaining two shades.

Proceed to the next color, which is darker. With a clean roller, stain the last one-third of the wall just like the first layer.

Finally, move on to the top space and stain as you did with the other two-thirds with the lightest colors of the three with a clean roller.

Spray some water in areas where one shade of paint is exposed to the next and moisten using a paintbrush or sea sponge. Ensure that it is not too damp.

Create a fading effect. You need to have the dullest color at the base and the lightest color towards the top above the middle color.

The same principles would still apply even if you want to use more than three-color shades. Always begin at the center and then advance towards the base of that band. After covering that area completely, shift to the upper side of the middle band.

Repeat the fading technique done on the three original strips. Proceed with the next two colors from the base to the top.

Read More

Easy Tips for Decorating With Paint

You don’t need to buy costly décor to beautify your home. Save a few hundred dollars by decorating with paint using these simple tips:

Interiors

Decorating With PaintThe illusion of lowering the ceiling comes by because of the simple act of employing the use of a dark color to paint the ceiling, creating a more intimate space.

Trims and walls can be painted using the same color and these aids in creating a common effect and as such, a semi-gloss paint goes to the trim with a flat paint being g used on the walls.

A tight or small space in a room can be made airier and larger by a simple act of a lighter shade of the color used on the walls applied to the ceiling, or a white color can as well do the job.

Exteriors

The front door of the house needs painting by a statement color that tends to stand out compared to every other color used. It should be something that is not so common such as the radiant ruby red or the traditional blue that is usually gorgeous.

The type of paint color used on the exterior walls of the house plays a critical role in how the whole world tends to see you besides the visitors and neighbors. Revitalizing the house once in 3 to 6 years with a new paint coat is a great practice.

Freshening up the trim helps in invigorating the exterior portion of the house without having to paint the entire exterior walls. The color of the exterior walls plays a huge role in the type of color to use, but a more neutral or white color would do.

Color

The type of color used in a room too plays a vital role in the kind of mood set for the room. Shades of different color create a more active and vibrant place that warms people up. Darker colors tend to create a relaxed and cooling down effect in a room.

Create a feminine classicism by the lacquer red, bronzed greens and ached-purple, inspired by the appliques, period of furniture and needlework back in style.

Unexpected forms of design, pattern, and color pairing, are aspects that one’s individuality can express depending on the choice of color paints used in a room.

Paint effects

The paint effects that are contemporary such as color washes and stencils creates surprise and interest especially when viewed regarding unframed artwork decorating the walls.

A sophisticated French look set up by the use of light painted strips especially when one uses the white, yellow or blue hues. A technique that adds sheen and texture to the room.

To the neutral walls, add a splash of color to a simple selection of ceiling or wall zones and painted differently. The color used should contrast that of the main wall. A technique commonly referred to as color blocking.

Accessories and accents

Use a new paint or coat of color to give the desks, tables, drawers and even the dresses a new lease of life, transforming the old and ugly furniture into a new bright and attractive peace in the house.

Application of splattered or dripped paint to furniture assists in getting in touch with the Pollock. A solid color best used for such mainly black or white before different paint shades used all over it.

A bold color to the kitchen makes it pop. Additionally, for the cabinetry backsplash, a favorite color would best suit the job as it is often easy to live with favorite colors.

Read More

Easy-To-Follow Simple Steps in Staining Your Deck

A deck is like an outdoor room, which is a perfect place to relax or entertain. However, since decks are highly exposed to numerous elements and foot traffic, they need maintenance from time to time to keep them protected. Staining of decks well assures one of additional barbecue years.

These simple steps will guide you and teach you how to stain decks and avoid unexpected happenings. With these easy-to-follow steps, you will also end up with a professional-looking deck that you will be proud.

Prepare the surface of the deck

Ensure the wood is dry and free of contaminants beforehand. Paint applied to damp or wet surfaces easily peel because of not adhering well to the surface.

A clean surface is equally important. The area need be free of dirt, mildew stains and any other forms of contaminants that would risk the whole process. Use an ideal cleaning agent to clean the surface and rinse with water before allowing it to dry for a few days.

A few ideas to note before you begin staining your deck.

  • Avoid the application of stain of direct sunlight.
  • In case, there is the likelihood of it raining anytime within the next twelve to twenty-four hours.
  • Before you paint the whole deck, test a small unnoticeable area just to be sure of the outcome.
  • If you want to paint a large surface requiring different gallons of paint, mix all paint in one container to ensure there is consistency all through.

Selecting the right stain

There is a broad range of stain and paints to choose from, and below is an overview of some that you could choose.

Clear stain and wood toned: these stains are lightly toned and bright, thus near transparent. Therefore, they allow for the visibility of texture and wood grain.

Semi-transparent: with this pigment, you are likely to see more color on the surface as compared to wood toner stains remain partly visible.

Semi-solid stains: semi-opaque or otherwise semi-solid stains covers most of the wood. However, it allows for some of the texture on the wood to remain visible.

Solid: if you want to hide your wood completely, this is the best finish to choose. With this finish, there is little wood left visible.

The application of stain

  • For you to work your way through the deck cells and wood fibers efficiently, natural bristled brushes are the best options to pick.
  • First, heavily coat the open-end grain of the boards, and then brush two to three boards at a time. With long smooth strokes, brush from one end of the board to the other.
  • Ensure that you maintain a wet edge at all times to avoid lap marks. You can also add wet stain onto wet stain instead of dry paint for similar results.
  • For new decks, only use one thin coat layer of oil-based deck finishes.
  • For decks created from recycled material, look out for your manufacturer’s instructions.
  • Keep in mind that too much stain is harmful. Over-application of stain leads to peeling and cracking when it gets in contact with moisture. It may also result in sticky. Therefore, the surface would not dry.

Preserve your stain

Remember, decks are exposed to constant abuse, so you have to reapply stain regularly now and then.

Read More